收藏本站

AN-744
RESET PIN ON THE ADUC7026 IS SCHMITT-TRIGGERED INTER-
NALLY THERE IS NO NEED TO USE AN EXTERNAL SCHMITT TRIGGER
ON THIS PIN.
WHEN INSERTED THE IRQ0 PUSH - BUTTON SWITCH DRIVES
P0.4/IRQ0 HIGH. THIS CAN BE USED TO INITIATE AN EXTERNAL
INTERRUPT 0.
TO ENTER SERIAL DOWNLOAD MODE THE USER MUST PULL THE
P0.0/BM PIN LOW WHILE RESET IS TOGGLED. ON THE EVALUA-
TION BOARD, SERIAL DOWNLOAD MODE CAN BE EASILY INITIATED
BY HOLDING DOWN THE SERIAL DOWNLOAD PUSH-BUTTON (S2)
WHILE INSERTING AND RELEASING THE RESET BUTTON (S3) AS
ILLUSTRATED IN FIGURE 1.
EXTERNAL MEMORY AND LATCH FOOTPRINT
FOOTPRINT FOR A 32 KB  16 STATIC RAM (CY7C1020CV33)
AND 16-BIT LATCH IS ALSO ON BOARD. SEE EXTERNAL MEMORY
INTERFACE SECTION.
DIP SWITCH LINK OPTIONS
S1-1 VREF
FUNCTION: CONNECTS THE OUTPUT OF THE 2.5 V EXTERNAL REFER-
ENCE (ADR291) TO THE VREF PIN (PIN 55) OF THE
ADUC7026.
USE: SLIDE S1-1 TO THE ON POSITION TO CONNECT THE
EXTERNAL REFERENCE TO THE ADUC7026.
??? ?? ??? ?? ???????
??? ???? ??
??? ???? ??
SLIDE S1-1 TO THE OFF POSITION TO USE THE INTERNAL
2.5 V REFERENCE OR A DIFFERENT EXTERNAL REFERENCE
ON VREF PIN OF J3 HEADER.
??
?????? ? ??
??
??? ? ??
??
?????? ? ??
??
??? ? ??
??
?????? ? ??
??
??? ? ??
S1-2 VOCM
FUNCTION: CONNECTS 1.67 V TO THE V OCM PIN OF THE AD8132.
??? ??????? ??
??? ??????? ??
USE:
NO EXTRA DC VOLTAGE IS REQUIRED ON THE BOARD
TO USE THE ADC IN DIFFERENTIAL MODE.
SLIDE S1-2 TO THE ON POSITION TO CONNECT V OCM
??
?????? ? ??
??
??? ? ??
??
?????? ? ??
??
??? ? ??
OF THE DIFFERENTIAL AMPLIfiER TO 1.67 V, DIVIDED
OUTPUT OF THE ADR291 REFERENCE.
FIGURE 1. ENTERING SERIAL DOWNLOAD MODE
ON THE EVALUATION BOARD
POWER INDICATOR/GENERAL-PURPOSE LEDS
A RED POWER LED (D3) IS USED TO INDICATE THAT A SUFfiCIENT
SUPPLY IS AVAILABLE ON THE BOARD. A GENERAL-PURPOSE LED
(D2) IS DIRECTLY CONNECTED TO P4.2 OF THE ADUC7026. WHEN
P4.2 IS CLEARED THE LED WILL BE TURNED ON, AND WHEN P4.2
SLIDE S1-2 TO THE OFF POSITION TO USE A DIFFERENT
VOLTAGE FOR V OCM BY CONNECTING A DC VOLTAGE TO
THE V OCM PIN OF J3 HEADER. NOTE THAT V OCM VALUE
IS DEPENDENT ON REFERENCE VALUE AS SHOWN IN
TABLE 1.
TABLE 1. V OCM RANGE
IS SET, THE LED WILL BE TURNED OFF.
ANALOG I/O CONNECTIONS
ALL ANALOG I/O ARE BROUGHT OUT ON HEADER J3.
ADC0 AND ADC1 ARE BUFFERED USING AN AD8606 TO EVALUATE
SINGLE-ENDED AND PSEUDO DIFFERENTIAL MODE. A POTENTIOMETER
V REF
2.5 V
2.048 V
1.25 V
V OCM MIN
1.25 V
1.024 V
0.75 V
V OCM MAX
2.05 V
2.276 V
2.55 V
CAN BE CONNECTED TO ADC0 BUFFERED.
ADC3 AND ADC4 CAN BE BUFFERED WITH A SINGLE-ENDED TO
DIFFERENTIAL OP AMP ON BOARD, THE AD8132, USED TO EVALU-
ATE THE ADC IN FULLY DIFFERENTIAL MODE.
S1-3 POT
FUNCTION: CONNECTS THE POTENTIOMETER OUTPUT TO ADC0.
THIS INPUT IS BUFFERED BY AN AD8606. THIS IS
FOR DEMONSTRATION PURPOSES.
ADC2 AND ADC5 TO ADC11 ARE NOT BUFFERED. BE SURE TO
USE:
SLIDE S1-3 TO THE ON POSITION TO CONNECT THE
FOLLOW THE DATA SHEET RECOMMENDATION WHEN CONNECTING
SIGNALS TO THESE INPUTS.
DAC1 CAN BE USED TO CONTROL THE BRIGHTNESS OF THE GREEN
LED D1, WHEN CONNECTED VIA THE S1 SWITCH.
GENERAL-PURPOSE PROTOTYPE AREA
GENERAL-PURPOSE PROTOTYPE AREAS ARE PROVIDED AT THE
POTENTIOMETER TO THE OP AMP OF ADC0 INPUT
CHANNEL.
SLIDE S1-3 TO THE OFF POSITION TO USE ADC0
INPUT ON J3 HEADER.
S1-4 ADC3
FUNCTION: BRINGS OUT ADC3 (PIN 64) ON J3 HEADER.
BOTTOM OF THE EVALUATION BOARD FOR ADDING EXTERNAL
COMPONENTS AS REQUIRED IN THE USER ’S APPLICATION. AS CAN
BE SEEN FROM THE LAYOUT AV DD , AGND, V DDIO , AND DGND
TRACKS ARE PROVIDED IN THIS PROTOTYPE AREA.
–2–
USE:
SLIDE S1-6 TO THE ON POSITION TO CONNECT
DIRECTLY ADC3 OF J3 HEADER TO ADC3 PIN
(PIN 64) OF THE ADUC7026.
SLIDE S1-6 TO THE OFF POSITION TO DISCONNECT
ADC3 OF J3 HEADER FROM ADC3 PIN (PIN 64) OF
THE ADUC7026.
REV. 0
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
EVAL-ADUC7060QSPZ KIT DEV QUICK START ADUC7060
EVAL-ADUC845QSPZ KIT DEV QUICK START ADUC845
EVAL-ADUM3070EBZ BOARD EVAL FOR ADUM3070
EVAL-SDP-CB1Z BOARD EVALUATION FOR SDP-CB1
EVB51JM128 BOARD EVAL FOR MCF51JM128 MCU
EVBQE128 BOARD EVAL FLEXIS QE128 FAMILY
F2068 PNL FIBERGLASS 18.44X14.44" WHT
FAN3100CMPX IC GATE DRVR SGL CMOS 2A 6MLP
相关代理商/技术参数
EVAL-ADUC7026QS-U1 制造商:Analog Devices 功能描述:QUICK START DEVL SYST EVAL BOARD I.C. - Bulk
EVAL-ADUC7026QSZ 功能描述:KIT DEV FOR ADUC7026/7027 RoHS:是 类别:编程器，开发系统 >> 通用嵌入式开发板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 标准包装:1 系列:PICDEM™ 类型:MCU 适用于相关产品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，线缆，元件，CD，PICkit 编程器 产品目录页面:659 (CN2011-ZH PDF)
EVAL-ADUC7028QSZ 功能描述:KIT DEV ADUC7028 QUICK START RoHS:是 类别:编程器，开发系统 >> 通用嵌入式开发板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 标准包装:1 系列:PICDEM™ 类型:MCU 适用于相关产品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，线缆，元件，CD，PICkit 编程器 产品目录页面:659 (CN2011-ZH PDF)
EVAL-ADUC7029QSZ 功能描述:EVAL DEV SYSTEM FOR ADUC7029 RoHS:否 类别:编程器，开发系统 >> 通用嵌入式开发板和套件（MCU、DSP、FPGA、CPLD等） 系列:* 标准包装:1 系列:PICDEM™ 类型:MCU 适用于相关产品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，线缆，元件，CD，PICkit 编程器 产品目录页面:659 (CN2011-ZH PDF)
EVAL-ADUC7029QSZ 制造商:Analog Devices 功能描述:Silicon Manufacturer:Analog Devices C
EVAL-ADUC7032QSPZ 制造商:Analog Devices 功能描述:EVAL BD FOR ADUC7032 - Bulk
EVAL-ADUC7033QSPZ 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk
EVAL-ADUC7034QSPZ 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits)